Showcase

Models Showcase

Models designed by Krypto, the SO3D robot, and by our members. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category

All Kitchen Desk & office Workshop Bedroom & bathroom Others
Preview of Grocery bag dispenser
By Krypto, the SO3D robot
Complexity
Simple
Others Sustainable living
0
Grocery bag dispenser
MAIN PURPOSE: Store and reuse carrier bags
Stuff used carrier bags in at the top and pull them out one at a time from the opening at the bottom; it hangs on the wall or inside a cupboard door from the two keyholes.
Printing notes
39.4 cm³
Volume
48.9 g
Est. weight
2,168
Triangles

Prints as shown on its floor, no supports. Large holes in the walls may need supports or good bridging.

AR view Open in app
Preview of Self-adhesive J hook
By Krypto, the SO3D robot
Complexity
Simple
Others Home hardware & architecture
0
Self-adhesive J hook
MAIN PURPOSE: Hang light items without drilling
A strong J hook for a towel, a bag or headphones that needs no drilling: stick it to tiles, glass or a cupboard door with a strip of double-sided foam tape on the flat back.
Printing notes
7.9 cm³
Volume
9.7 g
Est. weight
244
Triangles

Print lying flat so the layers run along the hook; PETG holds better than PLA.

AR view Open in app
Preview of Door wedge
By Krypto, the SO3D robot
Complexity
Simple
Others Home hardware & architecture
0
Door wedge
MAIN PURPOSE: Hold a door open
A slim 12-degree door wedge that grips: push the thin end under the door and it holds it open on wood, tile or carpet. It prints standing on its side; lay it down on its long, flat edge to use it.
Printing notes
61.4 cm³
Volume
76.1 g
Est. weight
152
Triangles

Print as it comes (wedge outline on the bed); PETG or TPU grips floors best.

AR view Open in app
Preview of Skirting board cable channel
By Krypto, the SO3D robot
Complexity
Simple
Others Home hardware & architecture
0
Skirting board cable channel
MAIN PURPOSE: Route cables along a wall
Runs a few cables neatly along a skirting board: screw or stick the channel down, press the cables past the two inner lips, and paint it to match the wall.
Printing notes
9.8 cm³
Volume
12.1 g
Est. weight
444
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Child-safe table corner cap
By Krypto, the SO3D robot
Complexity
Simple
Others Home hardware & architecture
0
Child-safe table corner cap
MAIN PURPOSE: Soften sharp furniture corners
Covers the sharp corner of a table or a shelf at toddler head height: the rounded cap slips over the corner and holds with a dab of double-sided tape inside. Print it as shown, then turn it over so the floor becomes the top.
Printing notes
3.0 cm³
Volume
3.8 g
Est. weight
1,840
Triangles

Print floor-down as shown, then turn it over to use it.

AR view Open in app
Preview of Garden post cap for 70 mm posts
By Krypto, the SO3D robot
Complexity
Simple
Others Home hardware & architecture
0
Garden post cap for 70 mm posts
MAIN PURPOSE: Protect the top of a wooden post
Caps a 70 mm square fence or pergola post so rain can't soak into the end grain; the ledge edge drips water clear of the post sides. Print it as shown, then turn it over so the floor becomes the top.
Printing notes
18.0 cm³
Volume
22.3 g
Est. weight
1,648
Triangles

Print in ASA or PETG for outdoor use. Print floor-down as shown, then turn it over to use it.

AR view Open in app
Preview of Radiator pipe cover rose
By Krypto, the SO3D robot
Complexity
Simple
Others Home hardware & architecture
0
Radiator pipe cover rose
MAIN PURPOSE: Cover the floor hole around a heating pipe
Hides the rough hole where a 15 mm radiator pipe comes out of the floor: spring the slit open, clip the rose round the pipe and slide it down to the floorboards. Print it as shown, then turn it over so the floor becomes the top.
Printing notes
7.5 cm³
Volume
9.3 g
Est. weight
1,596
Triangles

Print in PETG so it springs round the pipe. Print floor-down as shown, then turn it over to use it.

AR view Open in app
Preview of Constant-width roller
By Krypto, the SO3D robot
Complexity
Simple (set)
Others Science & education
0
Constant-width roller
MAIN PURPOSE: Demonstrate curves of constant width
Print three of these Reuleaux rollers, lay a book on top and roll it along: the book glides perfectly level even though the rollers are not round, a classic demonstration of curves of constant width.
Printing notes
22.2 cm³
Volume
27.5 g
Est. weight
780
Triangles

Prints as shown on its outline, no supports.

AR view Open in app
Preview of Hexagon cork coaster
By Krypto, the SO3D robot
Complexity
Simple
Others Geometric & decorative
0
Hexagon cork coaster
MAIN PURPOSE: Protect tables under drinks
A hexagonal coaster with a shallow recess for a 90 mm cork or felt disc; several of them tessellate into a honeycomb on the table.
Printing notes
21.9 cm³
Volume
27.2 g
Est. weight
88
Triangles

Prints as shown on its floor, no supports.

AR view Open in app
Preview of Lithophane light box
By Krypto, the SO3D robot
Complexity
Simple
Others Geometric & decorative
0
Lithophane light box
MAIN PURPOSE: Display a lithophane with a light behind it
Shows off a 100 mm lithophane: slide the printed panel into the slot behind the front window, put an LED tea light inside, and the picture glows; a USB light can come in through the back hole.
Printing notes
55.2 cm³
Volume
68.4 g
Est. weight
1,828
Triangles

Prints as shown on its floor, no supports. Large holes in the walls may need supports or good bridging.

AR view Open in app

SO3D.xyz is free and built by one maker. Help keep it running.

Be one of the first supporters this month.
Support · Buy me a coffeeSee the Hobbyist plan