Showcase

Models Showcase

Models designed by Krypto, the SO3D robot, and by our members. Open any of them in the generator to see exactly how it was built, remix it, or print it as-is. Browse the model library by category

All Kitchen Desk & office Workshop Bedroom & bathroom Others
Preview of Stick vacuum accessory pegs
By Krypto, the SO3D robot
Complexity
Advanced
Others Home hardware & architecture
0
Stick vacuum accessory pegs
MAIN PURPOSE: Store vacuum attachments on the wall
Screw the plate to the wall beside a stick vacuum and park its crevice tool, brush and extension on the three pegs. Print it lying flat; on the wall the pegs point straight out.
Printing notes
144.9 cm³
Volume
179.6 g
Est. weight
3,028
Triangles

Prints flat as a plate, no supports.

AR view Open in app
Preview of Chair caster cup
By Krypto, the SO3D robot
Complexity
Simple (set)
Others Home hardware & architecture
0
Chair caster cup
MAIN PURPOSE: Protect floors under casters
Stops chair and sofa casters rolling and scratching wooden floors: the wheel sits in the inner ring and the grip feet hold the cup still.
Printing notes
20.5 cm³
Volume
25.4 g
Est. weight
1,168
Triangles

Print four in TPU or PETG. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Cable and hose hanger
By Krypto, the SO3D robot
Complexity
Advanced
Others Home hardware & architecture
0
Cable and hose hanger
MAIN PURPOSE: Hang coiled cables and hoses
Coils an extension cable, a garden hose or a car charging cable on the wall: screw the plate up and loop the coil over the two long pegs. Print it lying flat.
Printing notes
157.3 cm³
Volume
195.0 g
Est. weight
2,340
Triangles

PETG with 4 walls; screw into a stud or masonry plugs. Prints flat as a plate, no supports.

AR view Open in app
Preview of Tablecloth clip
By Krypto, the SO3D robot
Complexity
Simple (set)
Others Home hardware & architecture
0
Tablecloth clip
MAIN PURPOSE: Keep tablecloths on outdoor tables
Clips a tablecloth to an outdoor table top 18 to 30 mm thick so a gust of wind can't lift it, sliding on from the edge with no tools.
Printing notes
13.1 cm³
Volume
16.3 g
Est. weight
392
Triangles

Print four in PETG lying flat.

AR view Open in app
Preview of Fly swatter
By Krypto, the SO3D robot
Complexity
Medium
Others Home hardware & architecture
0
Fly swatter
MAIN PURPOSE: Swat flies and wasps
A fly swatter with a slotted paddle that pushes less air ahead of it, so the fly doesn't feel it coming.
Printing notes
26.6 cm³
Volume
33.0 g
Est. weight
3,476
Triangles

Print in PETG for a bit of flex. Prints flat as a plate, no supports.

AR view Open in app
Preview of Chair leg glide caps
By Krypto, the SO3D robot
Complexity
Simple (set)
Others Home hardware & architecture
0
Chair leg glide caps
MAIN PURPOSE: Protect floors under chair legs
Slip a cap over each round chair leg up to 24 mm across and stick a felt pad in the recess underneath, so the chair glides quietly without scratching the floor. Print it as shown, then turn it over so the floor becomes the top.
Printing notes
5.1 cm³
Volume
6.4 g
Est. weight
1,008
Triangles

Print four in TPU or PETG. Print floor-down as shown, then turn it over to use it.

AR view Open in app
Preview of Curtain pole finial
By Krypto, the SO3D robot
Complexity
Medium
Others Home hardware & architecture
0
Curtain pole finial
MAIN PURPOSE: Finish a curtain pole end
A decorative end for a 25 mm curtain pole: push the socket onto the pole end and it stops the rings sliding off. Print it as shown, then turn it over so the floor becomes the top.
Printing notes
18.3 cm³
Volume
22.6 g
Est. weight
1,360
Triangles

Print floor-down as shown, then turn it over to use it.

AR view Open in app
Preview of Pipe floor flange
By Krypto, the SO3D robot
Complexity
Medium
Others Home hardware & architecture
0
Pipe floor flange
MAIN PURPOSE: Mount tubes for rails and shelving
A floor or wall flange for 20 mm conduit or dowel: screw it down through the four holes and push the tube into the socket to make clothes rails, light shelving or plant supports.
Printing notes
41.0 cm³
Volume
50.8 g
Est. weight
1,442
Triangles

Print in PETG with 5 walls; not for load-bearing handrails. Prints flat as a plate, no supports. Stacked parts are fused into one print.

AR view Open in app
Preview of Wall door bumper
By Krypto, the SO3D robot
Complexity
Simple
Others Home hardware & architecture
0
Wall door bumper
MAIN PURPOSE: Protect walls from door handles
Screw it to the wall where the door handle hits, and the rounded bumper takes the knock instead of the plaster.
Printing notes
10.3 cm³
Volume
12.8 g
Est. weight
848
Triangles

Print in TPU for a soft bump, or PETG. Prints as shown on its floor, no supports.

AR view Open in app
Preview of Rug corner gripper
By Krypto, the SO3D robot
Complexity
Simple (set)
Others Home hardware & architecture
0
Rug corner gripper
MAIN PURPOSE: Keep rug corners flat
Stops rug corners curling up and tripping people: stick a gripper under each corner with double-sided tape, and the grip feet hold it to the floor.
Printing notes
17.8 cm³
Volume
22.1 g
Est. weight
216
Triangles

Print four in TPU. Prints flat as a plate, no supports.

AR view Open in app

SO3D.xyz is free and built by one maker. Help keep it running.

Be one of the first supporters this month.
Support · Buy me a coffeeSee the Hobbyist plan